Freescale公司的MPC5676R是采用Power Architecture®技術的32位多核Qorivva MCU,主要用在汽車動力總成系統. MPC5676R集成了兩個180MHz處理器,三個第二代高性能時間處理器單元(eTPU2),6MB閃存,128路定時器(3 x eTPU2和1 x eMIOS),四個ADC,384KB RAM(數據存儲)以及不需要外接元件進行爆震檢測的信號處理電路.主要用在動力總成引擎控制,汽油直接注入,混合動力汽車, 爆震檢測,傳動控制等.本文介紹了MPC5676主要特性和優勢,方框圖以及Qorivva MPC567XEVB評估板主要組成與特性,以及相應電路圖.

The 32-bit Qorivva MPC5676R microcontroller (MCU) built on Power Architecture® technology is Freescale’s first multicore device designed for advanced powertrain control applications. The Qorivva MPC5676R performs four to five times better than previous-generation MCU families, addressing advanced filtering and signal processing requirements of direct injection, advanced diesel, hybrid electric and full electric powertrain applications to meet extreme regulatory and environmental requirements.

The Qorivva MPC5676R MCU achieves significant performance benchmarks with dual 180 MHz processors, three second-generation, high-performance time processor units (eTPU2), 6 MB of on-chip flash, 128-channel timers (3 x eTPU2s and 1 x eMIOS), quad ADCs, 384 KB RAM (for data storage) and on-chip digital signal processing capable of knock detection without the requirement of additional external components.

The Qorivva MPC5676R MCU is fully compatible with the Qorivva MPC567xF MCU, allowing automakers to incorporate this new technology easily for applications that require increased performance or memory expansion. Offering customers a seamless migration allows design re-use, and helps to reduce overall design cost and speed time to market.

The MPC5600 family of devices is closely compatible with the MPC5500 families, while introducing new features coupled with high performance CMOS technology to provide substantial reduction of cost per feature and significant performance improvement. This document describes the features of the MPC5676R and highlights important electrical and physical characteristics of this device.

The two e200z7 host processor cores of the MPC5676R are compatible with the Power Architecture Book E architecture. They are 100% user-mode compatible (with floating point library) with the classic PowerPC instruction set. The Book E architecture has enhancements that improve the architecture’s fit in embedded applications. In addition to the standard and VLE Power Architecture instruction sets, this core has additional instruction support for digital signal processing (DSP).

The MPC5676R has two levels of memory hierarchy; separate 16K instruction and 16K data caches for each of two cores and 384KB of on-chip SRAM. 6MB of internal flash memory is provided. An external bus interface is also available for special packaged parts to support application development and calibration.

MPC5676主要特性和優勢:

MPC5676目標應用:

• Powertrain engine control

• Gasoline direct injection

• Common rail diesel injection or clean diesel

• Hybrid electric vehicles

• Knock detection

• Cylinder or multi-valve deactivation

• Transmission control

• Continuously variable transmission

圖1.MPC5676方框圖

Qorivva MPC567XEVB評估板

The Qorivva MPC567XEVB is an evaluation system supporting both Qorivva MPC5674F and MPC5676R microprocessors. The complete system consists of a Qorivva MPC567XEVBMB motherboard that connects to either one of the following adapter cards: MPC567XADAT-PT4 (416PBGA), or MPC567XADAT-PT5 (516PBGA) daughter cards.

評估板包括:

Evaluation board (with socketed adapter board supporting both MPC567xF and MPC567xR)

P&E USB-ML-PPCNEXUS Hardware Interface Cable

XPC56xx Resources CD-ROM

MPC567XADAT-PT5 or MPC567XADAT-PT4

Warranty card

USB cable

MPC5674F/MPC5676R主板主要特性:

12VDC power supply input barrel connector (supply included)

2 CAN channels with jumper enables

2 SCI channels with jumper enables

One with transceiver and DB–9 Connector

One with transceiver and 0.10 header

1 LIN channel with jumper enables and Molex Connector

2 FlexRay channels with jumper enables

Both channels with transceiver and Molex Connector

4 user push button switches

1 8–position user dipswitch

8 user LEDs

3 potentiometer for analog voltage control

0.10 Pin headers for access to all I/O

2.5” x 2.5” prototyping area with 5V and GND rails

MPC567XADAT–PT5適配器板主要特性:

MPC567XADAT–PT5 has socket for either MPC547xF or MPC567xR in 516BGA foot print.

Jumper enables for all internal 1.2V regulator options (linear or switchmode)

External Synchronous SRAM (4Mbit) with jumper configurable Cs0/CS1 chip select

Socket for optional external oscillator

Robust Nexus and 14–pin JTAG debug connectors

MPC567XADAT–PT4適配器板主要特性:

MPC567XADAT–PT4 has socket for either MPC547xF or MPC567xR in 416BGA foot print.

Jumper enables for all internal 1.2V regulator options (linear or switchmode)

Socket for optional external oscillator

Robust Nexus and 14—pin JTAG debug connectors

圖2. MPC567XEVB評估板外形圖
MPC567XEVBMBSCH: 主板

圖3.MPC567XEVB主板電路圖(1)

圖4.MPC567XEVB主板電路圖(2)


圖5.MPC567XEVB主板電路圖(3)

圖6.MPC567XEVB主板電路圖(4)
MPC567XADAT416SCH:

圖7.MPC567XADAT–PT4適配器板電路圖(1)

圖8.MPC567XADAT–PT4適配器板電路圖(2)
MPC567XADAT516SCH:

圖9.MPC567XADAT–PT5適配器板電路圖(1)

圖10.MPC567XADAT–PT5適配器板電路圖(2)

圖11.MPC567XADAT–PT5適配器板電路圖(3)
詳情請見:
http://cache.freescale.com/files/32bit/doc/data_sheet/MPC5674F.pdf
和
http://cache.freescale.com/files/microcontrollers/hardware_tools/schematics/MPC567XEVBMBSCH.pdf?fpsp=1